Wood Archives - Poppytalk

DIY Dowel Clad Entertainment Unit Downunder

Jan Halvarson — Thu, 11 Nov 2021 06:57:00 +0000

Loved this DIY Dowel Clad Entertainment Unit project by Nyome Blanchard and her husband that I spotted on Instagram over the weekend so much, I asked her if we could share here on the blog.

Measuring in at just under five meters (approx. 16.5 feet) wide, they were determined to find a way to have a custom wall to wall built-in within their budget in their new home in Fern Bay, NSW (Australia).

Using 5 x 900 mm laundry top cabinet flat packs from a local hardware store, the couple wanted the project to be taller than a standard tv unit to give more visual weight in such a long space. They also needed it to be quite narrow so it didn’t impede on the usable space in the lounge room.

They clad the doors in half dowels and added a beautiful stone top. The result is stunning! Follow @lanchesbaybuild on Instagram as they continue working on their gorgeous home. In the meantime, check out the before/after progress!

Check out more on their new home journal Instagram account, @blanchesbaybuild.

The post DIY Dowel Clad Entertainment Unit Downunder appeared first on Poppytalk.

DIY Driftwood Magnets

Jan Halvarson — Fri, 08 Jan 2021 09:11:00 +0000

What works for me visually is the different colours and sizes of driftwood, along with her typed notes. Miranda is one of the best visual people around I think. Her Instagram accounts are so beautifully edited, yet don’t seem so pre-mediated (if you know what I mean). A must, must-follow! Also near the end of this post, I’ve added a few pics of her very special small batch soy and cedar wooden wicked candles that she sells through her webshop, maderagoods.ca. The scents are truly beautiful (I have one myself), and inspired by the outdoors here in the Pacific Northwest. All photos by Miranda Hudson.

maderagoods.ca

@maderagoods

@hudsonny

Check out the how Miranda made her magnets below.

DIY Driftwood Magnets

What you’ll need:

—A collection of small pieces of driftwood (but you could use any smaller found piece of nature — like seashells, river rocks, bark, lichen, acorns, etc.)

—small round magnets (found at most craft stores)

—glue gun

How to:

The how-to is pretty straightforward, using a glue gun and attaching each magnet to a piece of driftwood. The idea is so charming I think because half the fun would be the collecting in itself. So of course, the basics; making sure each piece is clean so that the glue will stick (no sand still attached, etc.), perhaps sanding edges a little if needed. So simple and easy, and such a beautiful way to greet the new year don’t you think? Thank you Miranda! We love this so much! Check out all the beautiful how-to visuals below.

The post DIY Driftwood Magnets appeared first on Poppytalk.

8 Plywood Headboard + Bed DIY Ideas

Jan Halvarson — Wed, 11 Oct 2017 05:34:00 +0000

You can never really go wrong with a minimalist look, and it seems that the plywood look has turned into a classic after all these years. It doesn’t really seem to be dating itself and if accessorized right, it can be a really great look on a budget. Here are a few that crossed our radar.

1. Floating Headboard
(Above). A perfect accessorized headboard from Gravity Home via Roomed.

2. Minimalist DIY Headboard
This project from Mr. Kate with three shelves is a nice touch.

3. How To Make a Double Duty Bedhead
A clever project from Homes to Love.

4. Finishing Touches
This one with a matching head and foot board is also finished. By Mark Tuckey via Inside Out Magazine.

5. DIY Simple Bedframe
A great project if you need a frame too! From The Merrythought.

6. Floating Bedside Boxes
We’re not only loving the floating bedside box shelves, but also the colour of this headboard from Piper Winston.

7. The Plywood Daybed
The ladies at The Merrythought made this brilliant daybed, now you can too! Click here for the how-to.

8. Nice Accessories
Also love how this one is accessorized by Miss Jettle.

The post 8 Plywood Headboard + Bed DIY Ideas appeared first on Poppytalk.

DIY Wooden Mobiles

Jan Halvarson — Wed, 19 Jul 2017 03:57:00 +0000

This past week we were inspired by our friendly neighborhood shop and workshop place, Collage Collage’s fun mobile project they posted on Instagram. I asked owner Erin Bonifero if she’s be interested in sharing the project on here on Poppytalk! This mobile project is something they do at their Crafternoon Campsthey are holding this summer at their Main Street shop here in Vancouver which anyone is welcome to sign up and join if you happen to be in the Vancouver area. Erin explains their inspiration and shares a few how-to photos below.

DIY Wooden Mobiles
By Erin Bonifero of Collage Collage

You will need
—Approx 9 or more different cut or scrap pieces of wood (some larger, some smaller) ranging anywhere from 1″ high (2.5 cm) to 12″ high (30 cm) —both approx. 1″ thick.
—eye hooks (1 for each mobile)
—bright coloured craft paints
—paint brush
—glue

Instructions
We were inspired by Bruno Munari and his amazing found object sculptures. We came across a simple painted piece of wood; and adapted it to best suit our 5-9yr old students. Under Russell Leng’s guidance the campers painted blocks of wood (a different colour or pattern on each side) and then stacked them to make a composition. We added an eye hook to the top + strung them up, spinning them to see what happened to the colours as they move. (See images below).

While we don’t offer a kit for this project yet – it IS something we’re doing at our Crafternoon Art Camps this summer. So Vancouver families can sign up and join us.

Visit Collage Collage
3697 Main St. (21st and Main)
Vancouver, BC V5V 3N7
Canada

And online:
Shop: shop.collagecollage.ca
Site collagecollage.ca
Instagram: @collagecollage
Facebook: CollageCollage

Also, check out Russell Leng’s work! He just launched a new side project!

The post DIY Wooden Mobiles appeared first on Poppytalk.

DIY Triangle Display Shelf

Jan Halvarson — Wed, 29 Mar 2017 07:29:00 +0000

Earlier last month we happened upon this triangle display shelf via Instagram from Moorea Seal in Seattle and were inspired that it was handmade. Ashley Miller(who works there) created it as a display shelf for the shop and so we asked these two ladies if they would be interested in sharing how it was made as a DIY for Poppytalk. And we were thrilled they agreed!

The result is a stunning shelf perfect for not only retail, but at home too. Also, be sure to check out both Moorea Seal online and Ashley’s Etsy shop, Charcoal and Ash. All equally impressive – more of their contact info below!

DIY Triangle Display Shelf

The inspiration for the Triangle Display Shelf was to create shelving that was useful and stylish that could also create height in the shallow shop widow spaces. The triangle shelf does a great job at creatively displaying store product without blocking light from the outdoors. The
removable bolts keep it safely attached they are a great feature allowing for repositioning and stacking. Once your triangle shelf is built you can customize it by painting, sanding, staining, or burning the surface for a variety of beautiful looks.

Shopping List:
• 9, 1”x 6”x 72” pine boards (1 board per triangle I recommend buying a few extra)
• 54 (6 per triangle) 1-5/8” wood screws
• 1/4” flat washers
• 1/4” -20 hex nuts
• 1/4” -20 x 2 carriage bolts
Instructions:
1. First cut at the end a 33 1/3 degree angle
2. Then turn the board over, slide it down to 21”
3. On the long side cut 33 1/3 degree angle again
4. Repeat until board is cut into 3 pieces, cut all boards
5. Fit pieces together (see image below)

6. Screw in 2 wood screws per corner, until all 9 triangles are assembled (see image below)

7. Stack bottom row 3 triangles right side up, 2 upside down (see image below).

8. Drill holes with 1/4” drill bit dead center through the triangles to connect them.
a. Not on the outside wall or on the bottom only where the triangles connect, to
hold them in place so they do not fall over when stacked.
9. Install 1/4” bolts, nuts, and washers.

10. Stack 2 triangles right side up and 1 upside down in center, on top of the bottom 5 triangles (see image below).

11. Repeat step 8. (But do drill through the bottom connecting triangles)
12. Stack final triangle on top, drill hole in the bottom and bolt

DIY by Ashley Miller
Etsy Shop: https://www.etsy.com/shop/CharcoalandAsh
Instagram: @charcoalandashpnw
Facebook: https://www.facebook.com/charcoalandash/

for

Moorea Seal

Founder: Moorea Seal

Where: 2523 3rd Ave, Seattle, WA

Open 7 days a week

mooreaseal.com

Instagram: @mooreaseal
Pinterest @mooreaseal
Twitter: @mooreaseal

The post DIY Triangle Display Shelf appeared first on Poppytalk.

DIY A Nature Mobile

Jan Halvarson — Wed, 09 Dec 2015 02:36:00 +0000

If you’re looking for a creative art book for kids this holiday season, might we suggest Susan Schwake’s new book, Art Camp, 52 Art Adventures for Kids to Explore. For ages 5+, Art Camp is an easy-to-use collection of self-guided open-ended lessons for kids using simple materials. A great go-to book to slip into a suitcase for vacation or backpack for an overnight as a great alternative to screen time and for some great art-making fun! Perfect for gifting and ideal for the family library! Susan has let us share one of the projects here on the blog today! Let’s take a look!

A Nature Mobile

Forget the kids! We love this mobile so much, we’re going to give it a go ourselves over the holidays! (Instructions below):

Art Camp is available through Amazon.com

The post DIY A Nature Mobile appeared first on Poppytalk.

DIY Desk Organizer

Jan Halvarson — Tue, 27 Jan 2015 08:12:00 +0000

Contributor post by Caitlin of The Merrythought.

I’ve really been diving into simplifying in big ways this year. Once I got mostly decluttered, I realized I really needed some storage solutions to help keep me organized and prevent me from buying items that I already have one of. This wooden desk organizer was a perfect project to help tackle the chaos that is always spread out in my workspace while also displaying the things I need and use in a lovely way!

Materials:
-Birch Plywood – 1 piece of the following sizes:
1/4″ x 12′ x 24″
1/8″ x 12″ x 24″
-Tape Measure
-Scroll Saw
-5/8″ Dowel
-Heavy Duty Super Glue
-Chalkboard Paint
-Masking Tape

Instructions:
-Use the scroll saw to cut the 1/4″ piece down to 19″ tall.
-From the small piece left over, measure and cut out a 6″ x 2″ piece and a 4″ x 2″ piece.
-Cut three 2.5″ pieces from the dowel.
-Measure and mark the pieces you will need to make the pockets on the 1/8″ piece of wood.
Pencil Pocket
One 3″ x 5″ piece
Two 1.5″ x 5″ pieces
One 1.5″ x 2.75″ piece

Chalk Pocket
One 1.5″ x 2″ piece
Two .75″ x 2″ pieces

Letters & Notebook Pocket
One 5″ x 6″ piece
Two 5″ x 1.5″ pieces
One 5.75″ x 1.5″ piece
-Use the scroll saw to cut out all of the pieces. Be sure to be precise in the cutting or they will not line up correctly.
-Use the heavy duty super glue to glue each of the pockets together.
-Once the pockets are dry and sturdy, attach the pockets, the dowels and the mini shelves (cut in the second step) using the super glue. (**It helps to lay out your pieces before you start gluing.)
-Let it dry according to directions.
-Use masking tape to mark off the area for the chalkboard and use chalkboard paint to fill in the space.
-Once everything is dry, you can leave it on your desk top or attach it to the wall and fill it with all your favorite desk essentials!

All of the measurements are just guidelines, you can change the sizes, add more pockets, add more paint… anything you want! Have fun and get organized!

The post DIY Desk Organizer appeared first on Poppytalk.

DIY Wooden Sign

Jan Halvarson — Wed, 06 Aug 2014 01:17:00 +0000

Contributor post by Rachel of the Crafted Life

It’s official: I’m in love with scroll saws! Unlike other intimidating power tools, there’s less of a risk when using them because the blade moves up and down instead of in a circular fashion (though please still use caution when attempting this project!). And while they are a bit of an investment, the possibilities of what you can create are endless!

Time: 2 hours + dry time
Materials: wood, scroll saw, sand paper, pencil, clear satin topcoat gel, rag, drill

Materials: The length of your wood will vary depending on the length of your saw’s neck, so be sure to measure this before beginning! I used a piece of Makore that was 14”L x 6”W x 3/4” thick.

Step One: If you aren’t great at free-handing text, play around in photoshop with different fonts and sizes. I chose Brannboll Fet at 340 pt. Instead of wasting ink on printing letters that size, I set the fill to 0% and had a stroke of 5 px.

Print then cut out to create a stencil.

Step Two: Lay your stencil on the wood then trace. You’ll use these marks as guidelines when cutting so they should be visible and clean

Step Three: Cut out using the scroll saw. Depending on how familiar you are with the saw, you may want to practice with a piece of pine and then work your way up to a more expensive wood. As long as you take your time and are patient, you should be able to get the hang of it. You can also choose a non-script font so that you can do the letters one by one.

Step Four: To get inside the loops of your letters, drill a small hole that goes all the way through the wood. You’ll then remove the blade on the scroll saw, feed through the hole (like you’re threading a needle), and reattach. Repeat until all of the letters are complete

Step Five: Sand to smooth out any rough edges.

Step Six: Apply your topcoat/stain/paint and let dry!

The post DIY Wooden Sign appeared first on Poppytalk.

DIY Pineapple Cutting Board

Jan Halvarson — Wed, 16 Jul 2014 06:21:00 +0000

Contributor post by Caitlin of The Merrythought

One of the things that I never seem to have enough of is cutting boards. Aside from every day use, I use them all the time for photoshoot styling and parties. They’re really easy to make at home and it’s nice to have a variety of sizes and shapes. Since pineapple patterns seem to be popping up all over the internet in shops and blogs, I thought a pineapple cutting board would be the perfect addition to my collection!

What you need:
-Piece of Hardwood (I used maple)
-Printer
-Pencil
-Scroll Saw
-Belt Sander
-Sandpaper
-Butcher Block Finish
-Pineapple image (download PDF file here)

How to make it:
-Print out your pineapple. You can download the image I used. (This PDF image will fit on a 6″ wide piece of wood – you can enlarge the image if you want a larger cutting board.)
-Trace pineapple onto the wood.
-Cut out the shape using a scroll saw. If you don’t cut right along the line in some spots, you can touch it up with the belt sander in the next step.

-Use a belt sander to smooth out the sides. I used a regular size sander for the bottom part and a 1″ belt sander for the top.
-Use a piece of sand paper to round the edges of the board.

-Wipe off the board and then apply butcher block oil or conditioner according to directions.

The post DIY Pineapple Cutting Board appeared first on Poppytalk.